PLZZ HELP

If you have two objects moving at the same velocity, would the object with bigger mass have higher or lower kinetic energy?​

Answers

Answer 1

Answer:

The kinetic energy of a moving object is directly proportional to its mass and directly proportional to the square of its velocity. This means that an object with twice the mass and equal speed will have twice the kinetic energy while an object with equal mass and twice the speed will have quadruple the kinetic energy.

Answer 2
Kinetic energy of a moving object

Related Questions

an airplane has a maximum velocity of 160km/h in still air. calculate its maximum velocity when it travels in air with a crosswind of 30km/h

Answers

Answer:

Velocity can be directly added or subtracted.

For example, if a boat has a velocity V in still water.

And now you put the boat in a river with a current that has a velocity V'

The total velocity of the boat in that river is just the addition of these two velocities.

Velocity in the river  = V + V'

Where the only tricky part is that the velocity is a vector, so you need to take in account the directions of each vector.

In this case, we have a plane with a maximum velocity of 160km, let's assume a direction for this velocity, let's say that is in the positive x-direction.

Then we can write the velocity in the vector form:

velocity  = (vel in x-axis, vel in y-axis)

The velocity of the plane can be written as:

v = (160km/h, 0)

Now we add a crosswind of 30km/h

crosswind means that it is perpendicular, then it acts on the y-axis.

Then the total velocity of the plane will be:

velocity = (160km/h, 0) + (0, 30km/h)

velocity = (160km/h, 30km/h)

Now you can compute the total velocity of the airplane as the module of that vector.

Remember that for a vector (x, y) the module is:

mod = √(x^2 + y^2)

Then the module of the velocity is:

v = √( (160km/h)^2 + (30km/h)^2) = 162.8 km/h

you are on a snorkeling trip. deep below the water, you look up at the surface of the water.

Answers

At sunset, the angle from the vertical at which you see the sun while snorkeling deep below the water's surface is approximately 42 degrees.

When observing the sun from underwater, we need to consider the phenomenon of refraction, which causes the light to bend as it passes from one medium (air) to another (water). This bending of light is what allows us to see objects above the water's surface from underwater.

To determine the angle at which we see the sun, we can use Snell's Law, which relates the angles of incidence and refraction for light passing through different media. Snell's Law states:

n₁ * sin(θ₁) = n₂ * sin(θ₂)

Where:

n₁ and n₂ are the refractive indices of the two media (air and water, respectively).

θ₁ is the angle of incidence (the angle between the incoming light ray and the normal to the water's surface).

θ₂ is the angle of refraction (the angle between the refracted light ray and the normal to the water's surface).

The refractive index of air is approximately 1.0003, and the refractive index of water is around 1.333. Since the light is coming from the air into the water, we can assume θ₁ (angle of incidence) to be 90 degrees, as it is perpendicular to the water's surface.

Using Snell's Law, we can calculate θ₂:

1.0003 * sin(90°) = 1.333 * sin(θ₂)

Simplifying the equation:

sin(θ₂) = (1.0003 / 1.333) * sin(90°)

sin(θ₂) ≈ 0.750

To find θ₂, we take the inverse sine (arcsine) of 0.750:

θ₂ ≈ arcsin(0.750)

θ₂ ≈ 48.6 degrees

However, this angle represents the angle from the normal to the water's surface, not the angle from the vertical. To find the angle from the vertical, we subtract θ₂ from 90 degrees:

The angle from the vertical = 90° - θ₂

The angle from the vertical ≈ 90° - 48.6°

The angle from the vertical ≈ 41.4 degrees

Rounded to two significant figures, the angle from the vertical at which you would see the sun at sunset while snorkeling deep below the water's surface is approximately 42 degrees.

When snorkeling deep below the water's surface and looking up at the sun during sunset, the sun would appear at an angle of approximately 42 degrees from the vertical. This angle takes into account the bending of light due to refraction as it passes from air to water.

To learn more about Angle, visit    

https://brainly.com/question/13200721

#SPJ11

An electromagnetic wave with frequency 65.0Hz travels in an insulating magnetic material that has dielectric constant 3.64 and relative permeability 5.18 at this frequency. The electric field has amplitude 7.20×10−3V/m. What is the wavelength of the wave?

Answers

Answer:

  The wavelength of the wave is [tex]1.06\times10^6 m[/tex]  

Explanation:

Lets calculate

We know an electromagnetic wave is propagating through an insulating magnetic material of dielectric constant K and relative permeability [tex]K_m[/tex] ,then the speed of the wave in this dielectric medium is [tex]\nu[/tex] is less than the speed of the light c and is given by a relation

               [tex]\nu=\frac{c}{\sqrt{KK_m} }[/tex]  --------- 1

In case the electromagnetic  wave propagating through the insulating magnetic material , the amplitudes of electric and  magnetic fields are related as -

             [tex]E_m_a_x= \nu B_m_a_x[/tex]

The magnitude of the 'time averaged value' of the pointing vector is called the intensity of the wave and is given by a relation

                       [tex]I = S_a_v[/tex]

                        [tex]\frac{E_m_a_xB_m_a_x}{2K_m\mu0}[/tex]----------- 3

now , we will find the speed of the propagation of an electromagnetic wave by using equation 1

[tex]\nu=\frac{c}{\sqrt{KK_m} }[/tex]

Putting the values ,

   =[tex]\nu= \frac{3.00\times10^8}{\sqrt{(3.64)(5.18)} }[/tex]

 =[tex]0.6908\times10^8m/s[/tex]

 = [tex]6.91\times10^7m/s[/tex]

Now , using this above solution , we will find the wavelength of the wave -

     [tex]\lambda=\frac{\nu}{f}[/tex]

    Putting the values from above equations -

  [tex]\frac{6.91\times10^7m/s}{65.0Hz}[/tex]

        [tex]\lambda= 1.06\times10^6 m[/tex]

Hence , the answer is [tex]\lambda= 1.06\times10^6 m[/tex]

Light enters glass from air. The angle of refraction will be A) greater than the angle of incidence. B) equal to the angle of incidence.

Answers

(B) The angle of refraction when light enters glass from air will be equal to the angle of incidence. This is in accordance with Snell's law, which relates the angles and refractive indices of the media involved.

Determine what is the Snell's law?

According to Snell's law, the relationship between the angle of incidence (θ₁), the angle of refraction (θ₂), and the refractive indices of the two media is given by:

n₁ sin(θ₁) = n₂ sin(θ₂),

where n₁ and n₂ are the refractive indices of the initial medium (air) and the second medium (glass), respectively.

When light travels from air to glass, the refractive index of air (n₁) is smaller than the refractive index of glass (n₂). As a result, the sine of the angle of refraction (θ₂) will be smaller than the sine of the angle of incidence (θ₁), given that the angles are measured with respect to the normal.

Since sin(θ₂) < sin(θ₁), the only way for Snell's law to hold true is if θ₂ is smaller than θ₁. Therefore, the angle of refraction will be equal to the angle of incidence, option B.

To know more about Snell's law, refer here:

https://brainly.com/question/31432930#

#SPJ4

A laser produces light of wavelength 615 nm in an ultrashort pulse.
What is the minimum duration of the pulse if the minimum uncertainty in the energy of the photons is 1.0%?

Answers

The minimum duration of the pulse is approximately 3.27 femtoseconds. This calculation is based on the uncertainty principle and the given uncertainty in energy, wavelength, and Planck's constant.

According to the uncertainty principle in quantum mechanics, there is a fundamental limit to the precision with which certain pairs of physical properties, such as energy and time, can be simultaneously known. In the case of light, the uncertainty principle relates the uncertainty in energy (∆E) to the uncertainty in time (∆t) through the equation:

∆E ∆t ≥ h/2π

where ∆E is the uncertainty in energy, ∆t is the uncertainty in time, and h is Planck's constant (approximately 6.626 × 10^(-34) J·s).

We are given the uncertainty in energy as 1.0% of the total energy of the photons. This can be expressed as:

∆E = 0.01 × E

where E is the total energy of the photons.

The energy of a photon can be calculated using the equation:

E = hc/λ

where h is Planck's constant, c is the speed of light in a vacuum (approximately 3.0 × 10^8 m/s), and λ is the wavelength of the light.

Substituting the given wavelength into the equation:

E = (6.626 × 10^(-34) J·s × 3.0 × 10^8 m/s) / (615 × 10^(-9) m)

E ≈ 3.22 × 10^(-19) J

Substituting the value of ∆E into the uncertainty principle equation:

0.01 × E ∆t ≥ h/2π

0.01 × (3.22 × 10^(-19) J) ∆t ≥ (6.626 × 10^(-34) J·s) / (2π)

0.01 × (3.22 × 10^(-19) J) ∆t ≥ 1.05 × 10^(-34) J·s

∆t ≥ (1.05 × 10^(-34) J·s) / (0.01 × 3.22 × 10^(-19) J)

∆t ≥ 3.27 × 10^(-15) s

To convert the time to femtoseconds (fs), we multiply by 10^15:

∆t ≈ 3.27 fs

Therefore, the minimum duration of the pulse is approximately 3.27 femtoseconds.

The minimum duration of the pulse is approximately 3.27 femtoseconds. This calculation is based on the uncertainty principle and the given uncertainty in energy, wavelength, and Planck's constant.

To know more about Planck's constant visit:

https://brainly.com/question/30991884

#SPJ11

Explain why, in terms of forces, there is a risk of head injury when diving from this height. Suggest why the high divers would choose to enter the water feet first.

Answers

Answer:

Due to lower risk of injury or damage.

Explanation:

The high divers would choose to enter the water from the feet first because there is low risk of injury. The brain is the most important part of the body which very sensitive to any small injury. Small injury to brain leads to big problems in life. High divers can reach speeds of nearly 60 mph and enters about 28m into the water in about three seconds which can damage the head region if comes in contact with the ground so this is the reason the high divers avoid of entering in the water through their heads and choose entering through their feet.

A satellite of mass 180 kg is placed into Earth orbit at a height of 100 km above the surface. (a) Assuming a circular orbit, how long does the satellite take to complete one orbit?
1.47
h
(b) What is the satellite's speed?
7430
m/s
(c) Starting from the satellite on the Earth's surface, what is the minimum energy input necessary to place this satellite in orbit? Ignore air resistance but include the effect of the planet's daily rotation.
7.33e+09
J

Answers

(a) The satellite takes approximately 1.47 hours to complete one orbit.

(b) The satellite's speed is approximately 7430 m/s.

(c) The minimum energy input necessary to place the satellite in orbit, starting from the Earth's surface, is approximately 7.33 x 10^9 J.

Determine how the satellite take to complete one orbit?

(a) To determine the time taken to complete one orbit, we can use Kepler's third law, which states that the square of the orbital period (T) is proportional to the cube of the semi-major axis (a) of the orbit.

Since the satellite is in a circular orbit, the semi-major axis is equal to the radius of the orbit, which is the sum of the Earth's radius (R) and the height above the surface (h). Using the given values, we can calculate T as follows:

T² = (4π² / GM) * a³

T² = (4π² / GM) * (R + h)³

T = √[(4π² / GM) * (R + h)³]

Substituting the known values, we find T ≈ 1.47 hours.

Determine how to find the satellite speed?

(b) The speed of the satellite can be determined using the formula for orbital speed:

v = √(GM / r)

where G is the gravitational constant, M is the mass of the Earth, and r is the distance from the center of the Earth to the satellite's orbit (R + h). Plugging in the values, we find v ≈ 7430 m/s.

Determine what is the minimum energy input?

(c) The minimum energy input required to place the satellite in orbit can be calculated as the sum of the gravitational potential energy and the kinetic energy of the satellite. The gravitational potential energy is given by:

PE = -GMm / r

where m is the mass of the satellite and r is the distance from the center of the Earth to the satellite's orbit (R + h). The kinetic energy is given by:

KE = 0.5mv²

Plugging in the values, we find the minimum energy input is approximately 7.33 x 10^9 J.

To know more about potential energy, refer here:

https://brainly.com/question/24284560#

#SPJ4

what is the phenomenon that allows the sun's heat to pass through to the earth's surface while stopping it from spreading back into space?

Answers

The phenomenon that allows the Sun's heat to pass through to the Earth's surface while stopping it from spreading back into space is the greenhouse effect.

What is the greenhouse effect?

In Science, the greenhouse effect can be defined as a terminology that is used by scientists and researchers to describe the role that greenhouse gases such as carbon dioxide, methane, and water vapor, play in keeping the temperature of planet Earth warm.

Generally speaking, greenhouse effect help in the regulation of atmospheric temperature during the day and at night.

However, it is important to note that the greenhouse effect does not result in a fall or decrease in sea levels and lower rainfall in coastal zones.

Read more on greenhouse effect here: brainly.com/question/19521661

#SPJ4

A quasar is observed with a redshift of z = 3.7. What will be the wavelength of the observed Lyman-alpha line from this quasar? wavelength: ___ nm
This is in the visible part of the clectromagnetic spectrum.

Answers

The wavelength of the observed Lyman-alpha line from this quasar with a redshift of z = 3.7 will be approximately 444 nm.

The formula to calculate the observed wavelength (λ_obs) of an object with redshift (z) is given by:

λ_obs = λ_rest * (1 + z)

In this case, we are interested in the Lyman-alpha line, which has a rest wavelength (λ_rest) of 121.6 nm.

Substituting the values into the formula, we have:

λ_obs = 121.6 nm * (1 + 3.7)

λ_obs = 121.6 nm * 4.7

λ_obs ≈ 570.32 nm

However, it's important to note that the Lyman-alpha line falls in the ultraviolet (UV) region of the electromagnetic spectrum, not in the visible part.

Since the question specifically mentions that it is in the visible part, it suggests a typographical error or some other contextual discrepancy.

The wavelength of the observed Lyman-alpha line from this quasar, assuming a redshift of z = 3.7, is approximately 570.32 nm.

However, the Lyman-alpha line is in the ultraviolet (UV) region, not the visible part of the electromagnetic spectrum.

To know more about quasar visit:

https://brainly.com/question/20308478

#SPJ11

1. Find the density of the N nucleus. 2. The binding energy per nucleon E, of the lithium isotope Li is 5.6 MeV/nucleon. Find its atomic mass of this isotope. 3. Find the energy needed to remove a proton from the nucleus of the potassium isotopek

Answers

The density of the N nucleus can be calculated by dividing its mass by its volume, the binding energy per nucleon E of the lithium isotope Li is [tex]5.6 MeV/nucleon[/tex], the energy needed to remove a proton from the nucleus of the potassium isotope K is [tex]289.77 MeV[/tex]

The mass number of N is 14 and its atomic number is 7. The number of neutrons in the N nucleus is given by [tex]14 - 7 = 7[/tex] neutrons.

The mass of one neutron is about 1.008665 atomic mass units (amu) or [tex]1.67493 \times 10^{-27} kg[/tex].

The mass of the N nucleus = [tex]7(1.008665) + 7.016004 = 14.04273 $ amu[/tex]. Thus, the density of the N nucleus can be calculated by dividing its mass by its volume.

The binding energy per nucleon E of the lithium isotope Li is 5.6 MeV/nucleon. To find its atomic mass of this isotope, the mass defect of the nucleus is calculated using the formula:

Mass defect = (Zmp + Nmn) - M

where

Z = number of protons, N = number of neutrons, mp = mass of a proton, mn = mass of a neutron, M = mass of the nucleus.

The mass of a proton is approximately [tex]1.00728 amu[/tex], while the mass of a neutron is approximately [tex]1.00866 amu[/tex].

Mass defect = [tex](3 \times 1.00728 + 4 \times 1.00866) - 7.01600[/tex]Mass defect = [tex]0.126 $ amu[/tex]Atomic mass of [tex]Li-7 = 7.01600 - 0.126[/tex]Atomic mass of [tex]Li-7 = 6.89 amu[/tex]

The energy needed to remove a proton from the nucleus of the potassium isotope K can be calculated using the formula:

Binding energy = [tex]E \times A[/tex]

where E is the binding energy per nucleon, A is the mass number. Binding energy of K isotope = 7.43 MeV/nucleon (given)

Mass number of K isotope = [tex]39[/tex]Binding energy = [tex]7.43 \times 39[/tex]Binding energy = [tex]289.77 MeV[/tex]

Thus, the energy needed to remove a proton from the nucleus of the potassium isotope K is [tex]289.77 MeV[/tex].

Learn more about The density: brainly.com/question/1354972

#SPJ11

Which of the following is another name for a convex lans?
O Diverging liens
3. Converging lens
O c Shrinking lans
OD Security lans

Answers

I am going with D hope that helps

Answer:

3. converging lens

Explanation:

When the rays of light coming parallel to principle axis after refraction through the lens passes through a point called focus, since it converge all the ray at one point, that is why it is said to be converging lens.

Block 1 is attached to a spring and oscillates on a horizontal frictionless surface. When block 1 is at a point of maximum displacement, block 2 is placed on top of it from directly above without interrupting the oscillation, and the two blocks stick together. How do the maximum kinetic energy and period of oscillation with both blocks compare to those of block 1 alone?
a. Maximum Kinetic energy - smaller, Period - smaller
b. Maximum Kinetic energy - smaller, Period - greater
c. Maximum Kinetic energy - The same, Period - smaller
d. Maximum Kinetic energy - The same, Period - greater

Answers

The correct answer is: a. Maximum Kinetic energy - smaller, Period - smaller. When block 2 is placed on top of block 1 without interrupting the oscillation, the system's mass increases.

As a result, the effective mass of the combined blocks increases, which leads to a decrease in the maximum kinetic energy of the system. This is because the kinetic energy is directly proportional to the mass of the system. Additionally, the period of oscillation is determined by the mass and the spring constant of the system. With an increase in the combined mass of the blocks, the period of oscillation becomes smaller. This is because the effective mass affects how quickly the system can oscillate back and forth, and a larger mass requires more time to complete each oscillation. Therefore, when block 1 and block 2 stick together, the maximum kinetic energy decreases compared to block 1 alone, and the period of oscillation also decreases.

To learn more about Kinetic energy, Click here:

https://brainly.com/question/16012885

#SPJ11

Two protons are aimed directly toward each other by a cyclotron accelerator with speeds of 2.20×105 m/s, measured relative to the earth.
Find the maximum electrical force that these protons will exert on each other.

Answers

The maximum electrical force that these protons will exert on each other is 2.48 x 10^-13 N.

The electrical force between two charged particles can be calculated using Coulomb's Law:

F = (k * q1 * q2) / r^2

Where:

F is the electrical force,

k is the electrostatic constant (k ≈ 8.99 x 10^9 N m^2/C^2),

q1 and q2 are the charges of the particles (in this case, both are protons, so each charge is q = 1.6 x 10^-19 C),

and r is the distance between the particles (assuming they are in contact, r ≈ 2 x 10^-15 m).

To find the maximum electrical force, we need to calculate the force when the protons are closest to each other. This occurs when they are just about to collide, so their separation distance is equal to the sum of their radii (r ≈ 2 x 10^-15 m).

Plugging the values into the formula, we have:

F = (8.99 x 10^9 N m^2/C^2) * (1.6 x 10^-19 C) * (1.6 x 10^-19 C) / (2 x 10^-15 m)^2

F ≈ 2.48 x 10^-13 N

The maximum electrical force that these protons will exert on each other is approximately 2.48 x 10^-13 N. This force arises due to the interaction between their positive charges and is inversely proportional to the square of the distance between them.

To know more about electrostatic visit :

https://brainly.com/question/17692887

#SPJ11

A tank contains 2 m3 of air at -93°C and a gage pressure Ro6 of 1.4 MPa. Determine the mass of air, in kg. The local atmospheric pressure is 1 atm

Answers

To determine the mass of air in the tank, we need to convert the given parameters and apply the ideal gas law. The mass of air in the tank is approximately 5.04 kg.

To determine the mass of air in the tank, we need to consider the ideal gas law and convert the given parameters to appropriate units.

Given:

Volume of air (V) = 2 m³

Temperature (T) = -93°C

Gauge pressure (P) = 1.4 MPa

Local atmospheric pressure (P_atm) = 1 atm

First, let's convert the temperature from Celsius to Kelvin:

T = -93°C + 273.15 = 180.15 K

Next, we need to convert the gauge pressure to absolute pressure by adding the atmospheric pressure:

P_abs = P + P_atm = 1.4 MPa + 1 atm = 2.4 MPa

Now, we can use the ideal gas law equation to calculate the mass of air (m):

PV = nRT

Where:

P = absolute pressure

V = volume

n = number of moles of air

R = ideal gas constant

T = temperature

Rearranging the equation to solve for mass (m):

m = (n * M) / N_A

Where:

M = molar mass of air

N_A = Avogadro's number

To find the number of moles (n), we can use the equation:

n = PV / RT

Given that the molar mass of air is approximately 28.97 g/mol, and the ideal gas constant R is 8.314 J/(mol·K), we can calculate the mass of air.

Calculations:

n = (P_abs * V) / (R * T)

m = (n * M) / N_A

Substituting the values:

n = (2.4 MPa * 2 m³) / (8.314 J/(mol·K) * 180.15 K)

m = (n * 28.97 g/mol) / 6.022 x 10^23 mol⁻¹

Calculating the mass of air (m):

m ≈ 5.04 kg

Therefore, the mass of air in the tank is approximately 5.04 kg.

To know more about parameters, click here https://brainly.com/question/29728062

#SPJ11

An object with mass 2.7 kg is executing simple harmonic motion, attached to a spring with spring constant k = 310 N/m. When the object is 0.020 m from its equilibrium position, it is moving with a speed of 0.55 m/s. (a) Calculate the amplitude of the motion. (b) Calculate the maximum speed attained by the object.
a.The amplitude of the motion is \(0.02\;{\rm{m}}\).
bThe maximum speed attained by the object is \(0.352\;{{\rm{m}} \mathord{\left/{\vphantom {{\rm{m}} {\rm{s}}}} \right.} {\rm{s}}}\).

Answers

The amplitude of the motion is 0.02 m. The maximum speed attained by the object is 0.352 m/s.

a.

In simple harmonic motion (SHM), the displacement of an object from its equilibrium position can be described by the equation:

x(t) = A * cos(ωt + φ)

where:

x(t) is the displacement at time t,

A is the amplitude of the motion,

ω is the angular frequency,

t is the time, and

φ is the phase constant.

The speed of the object is given by:

v(t) = A * ω * sin(ωt + φ)

Mass of the object, m = 2.7 kg

Spring constant, k = 310 N/m

Displacement from equilibrium position, x = 0.02 m

Speed of the object, v = 0.55 m/s

We can relate the angular frequency (ω) to the mass and spring constant using the equation:

ω = sqrt(k / m)

Let's calculate ω first:

ω = sqrt(310 N/m / 2.7 kg) ≈ 8.064 rad/s

To find the amplitude (A), we can use the given displacement:

0.02 m = A * cos(0 + φ)

cos(0) = 1

Therefore, we have:

A = 0.02 m

The amplitude of the motion is 0.02 m.

b.

The maximum speed in simple harmonic motion occurs when the displacement is zero (i.e., at the equilibrium position). At this point, the speed is at its maximum value.

Amplitude of the motion, A = 0.02 m

We can find the maximum speed (v_max) using the equation:

v_max = A * ω

Substituting the values:

v_max = 0.02 m * 8.064 rad/s ≈ 0.352 m/s

Conclusion:

The maximum speed attained by the object is 0.352 m/s.

To know more about amplitude visit:

https://brainly.com/question/3613222

#SPJ11

state two other ways in which evaporation is different from boiling​

Answers

evaporation is slower, occurs only from the surface of the liquid, does not produce bubbles, and leads to cooling. boiling is faster, can occur throughout the liquid, produces lots of bubbles, does not result in cooling

an athlete whirls an 11,7 kg hammer tied to the end of a 1,2 m chain in a simple horizontal circle where you should ignore any vertical deviations. the hammer moves at the rate of 0,489 rev/s. what is the tension along the chain?

Answers

The tension along the chain, when an 11.7 kg hammer is whirled at a rate of 0.489 rev/s in a simple horizontal circle with a 1.2 m chain, is approximately 140.79 N.

To find the tension along the chain, we can analyze the forces acting on the hammer in circular motion.

In this case, the tension in the chain provides the centripetal force required to keep the hammer moving in a circle.

The centripetal force is given by the formula:

F = m * v² / r

Where:

F is the centripetal force

m is the mass of the hammer

v is the velocity of the hammer

r is the radius of the circular path

m = 11.7 kg

v = 0.489 rev/s (angular velocity)

r = 1.2 m

To calculate the linear velocity, we need to convert the angular velocity to linear velocity. The formula for converting angular velocity to linear velocity is:

v = ω * r

Where:

v is the linear velocity

ω is the angular velocity

r is the radius of the circular path

Substituting the values, we have:

v = 0.489 rev/s * 2π radians/rev * 1.2 m

v ≈ 3.678 m/s

Now we can calculate the centripetal force:

F = (11.7 kg) * (3.678 m/s)²/ 1.2 m

F ≈ 140.79 N

Therefore, the tension along the chain is approximately 140.79 N.

The tension along the chain, when an 11.7 kg hammer is whirled at a rate of 0.489 rev/s in a simple horizontal circle with a 1.2 m chain, is approximately 140.79 N.

To know more  about tension visit:

https://brainly.com/question/29466375

#SPJ11

an electron is in the ground state of an infinite square well. the energy of the ground state is e1 = 0.86 ev. use hc=1240 nm ev.
(a) What wavelength of electromagnetic radiation would be needed to excite the electron to the n = 3 state?
nm
(b) What is the width of the square well?
nm

Answers

a) The wavelength of electromagnetic radiation needed to excite the electron to the n = 3 state is approximately 1808.26 nm.

b) The width of the square well is approximately 904.13 nm.

To find the wavelength of electromagnetic radiation needed to excite the electron to the n = 3 state, we can use the formula:

λ = hc / ΔE

where λ is the wavelength, h is Planck's constant (6.626 × 10⁻³⁴ J·s), c is the speed of light (2.998 × 10⁸ m/s), and ΔE is the energy difference between the two states.

First, let's convert the energy difference ΔE from electron volts (eV) to joules (J):

ΔE = (3² - 1²) x e₁

ΔE = (9 - 1) x 0.86 eV

ΔE = 8 x 0.86 eV

ΔE = 6.88 eV

Next, let's convert the energy difference ΔE from eV to joules (J):

1 eV = 1.602 × 10⁻¹⁹ J

ΔE = 6.88 x 1.602 × 10⁻¹⁹ J

ΔE ≈ 1.101376 × 10⁻¹⁸ J

Now we can calculate the wavelength λ:

λ = (hc) / ΔE

λ = (6.626 × 10⁻³⁴ J·s x 2.998 × 10⁸ m/s) / (1.101376 × 10⁻¹⁸ J)

λ ≈ 1.80826 × 10⁻⁶ m

Finally, let's convert the wavelength from meters (m) to nanometers (nm):

1 m = 1 × 10⁹ nm

λ ≈ 1.80826 × 10⁻⁶ m x 1 × 10⁹ nm/m

λ ≈ 1808.26 nm

Therefore, the wavelength of electromagnetic radiation needed to excite the electron to the n = 3 state is approximately 1808.26 nm.

To find the width of the square well, we can use the formula:

L = λ / 2

where L is the width of the square well.

Using the value we calculated for λ in part (a):

L = 1808.26/2 nm

L = 904.13 nm

Therefore, the width of the square well is approximately 904.13 nm.

To know more about electromagnetic radiation follow

https://brainly.com/question/27431416

#SPJ4

1.45 L of 16°C water is placed in a refrigerator. The refrigerator's motor must supply an extra 10.7 W power to chill the water to 6°C in 0.7 hr. What is the refrigerator's coefficient of performance?

Answers

Answer:

The coefficient of performance of the refrigerator is 2.251.

Explanation:

In this case, the coefficient of performance of the refrigerator ([tex]COP[/tex]), no unit, is equal to the ratio of the heat rate received from the water to the power needed to work, that is:

[tex]COP = \frac{\dot Q_{L}}{\dot W}[/tex] (1)

[tex]COP = \frac{\rho\cdot V\cdot c_{w}\cdot \Delta T}{\dot W \cdot \Delta t}[/tex] (2)

Where:

[tex]\dot Q_{L}[/tex] - Heat rate received from the water, in watts.

[tex]\dot W[/tex] - Power, in watts.

[tex]\rho[/tex] - Density of water, in kilograms per cubic meter.

[tex]V[/tex] - Volume of water, in cubic meters.

[tex]c_{w}[/tex] - Specific heat of water, in joules per kilogram-degree Celsius.

[tex]\Delta T[/tex] - Temperature change, in degrees Celsius.

[tex]\Delta t[/tex] - Cooling time, in seconds.

If we know that [tex]\rho = 1000\,\frac{kg}{m^{3}}[/tex], [tex]V = 1.45\times 10^{-3}\,m^{3}[/tex], [tex]c_{w} = 4187\,\frac{J}{kg\cdot ^{ \circ}C}[/tex], [tex]\Delta T = 10\,^{\circ}C[/tex], [tex]\dot W = 10.7\,W[/tex] and [tex]\Delta t = 2520\,s[/tex], then the coefficient of refrigeration of the refrigerator is:

[tex]COP = \frac{\rho\cdot V\cdot c_{w}\cdot \Delta T}{\dot W \cdot \Delta t}[/tex]

[tex]COP = 2.251[/tex]

The coefficient of performance of the refrigerator is 2.251.

If the velocity of an object is v=-5t+30, at what time does it change direction? Ot=6 O t=5 Ot=3 Ot=2 Ot=0

Answers

Option (A) t = 6 , is the correct option .

The object changes direction at t = 6. The given velocity equation is v = -5t + 30, where v represents velocity and t represents time.

To determine when the object changes direction, we need to find the time at which the velocity becomes zero. The given velocity equation is v = -5t + 30, where v represents velocity and t represents time.

Setting the velocity equation equal to zero, we have:

-5t + 30 = 0

To solve for t, we can isolate t by subtracting 30 from both sides of the equation:

-5t = -30

Next, divide both sides of the equation by -5 to solve for t:

t = -30 / -5

t = 6

The object changes direction at t = 6. At this time, the velocity becomes zero.

To know more about velocity ,visit:

https://brainly.com/question/80295

#SPJ11

When describing a thermodynamic system, which is a good description of "internal energy"?

Answers

In summary, the internal energy of a thermodynamic system is the sum of the potential and kinetic energy of all the particles in the system. It is a property of the system that depends only on the current state of the system and can be affected by a number of factors such as temperature, pressure, and composition of the system.

Internal energy is the energy that is associated with the microscopic components of the system, such as molecules and atoms. The internal energy of a thermodynamic system is the total potential energy and kinetic energy of all of the particles in the system. It includes the energy that is stored in the bonds between atoms and molecules and the kinetic energy of the individual particles. The internal energy of a thermodynamic system is a property of the system that depends only on the current state of the system. It can be increased or decreased by adding or removing heat or work from the system. "The internal energy of a system can be represented by the symbol U. "There are many factors that can affect the internal energy of a thermodynamic system. These include the temperature, pressure, and composition of the system, as well as any external forces that are acting on the system. The internal energy of a thermodynamic system is a key concept in the study of thermodynamics, as it helps to describe the behavior of systems as they undergo changes in temperature, pressure, and other variables.

to know more about Internal energy visit:

https://brainly.com/question/11278589

#SPJ11

The frequency of a sound wave is 457 Hz and the speed is
342.5 m/s. What is the sound's wavelength?

Answers

Answer:

/\ = 0.75m

Explanation:

v = f × /\

342.5= 457/\

/\ = 0.75m

Indicate the direction of the magnetic force. A positive charge travels to the right of the page through a magnetic field that points into the page. Which way does the magnetic force point?

A. Up along the page
B. Down along the page
C. Left
D. Right

PLS HELP ㅠㅠ

Answers

Explanation:

A. Up along the page

Using the law of the right hand

The only players permitted to wear mitts over gloves are _________.
1 the pitcher and first base player
2 the catcher and outfielder
3 the catcher and first base player
4 the catcher and pitcher

Answers

Answer:

the catcher and outfielder

Explanation:

Answer: The catcher and the player at first base are the only players permitted to wear mitts rather than gloves. So, the answer would be 3.

Explanation: I had this on a quiz and got it right.

Hope this helps!

An amusement park builds a ride in which the victim is made to spin about a pole with a rocket strapped on his seat. The rider, box and rocket have an initial total mass of 170 kg. Neglect the mass of the rod of length 6 m .What is the moment of inertia of rider, box and rocket about the pole? The acceleration of gravity is 9.8 m/s^2 . Treat the rider, box and rocket as a point mass. Answer in units of kg · m^2
B) The rocket develops a thrust of 98 N perpendicular to the path of the rider. What is the initial angular acceleration of the rider? Answer in units of rad/s^2
C)After what time t is the rider’s velocity equal to 5 m/s? Neglect the change in mass of the rocket. Answer in units of s.
D)Gas exits the rocket at vt = 390 m/s. What mass per second must leave to develop the thrust F given above? Answer in units of kg/s .

Answers

The moment of inertia of the rider, box, and rocket about the pole is 170 kg * (6 m)^2 = 6120 kg · m^2.  The initial angular acceleration of the rider is 0.098 rad/s^2.

A) The moment of inertia of the rider, box, and rocket about the pole can be calculated using the formula for the moment of inertia of a point mass rotating around an axis. The moment of inertia (I) is given by the product of the mass (m) and the square of the distance (r) from the axis of rotation:

I = m * r^2

Since the mass of the rider, box, and rocket is given as 170 kg and the rod is neglected, the moment of inertia will be the same for all components. Therefore, the moment of inertia of the rider, box, and rocket about the pole is 170 kg * (6 m)^2 = 6120 kg · m^2.

B) The initial angular acceleration of the rider can be determined using Newton's second law of rotational motion, which states that the torque (τ) is equal to the moment of inertia (I) multiplied by the angular acceleration (α). The torque can be calculated as the product of the force (F) applied perpendicular to the path of the rider and the distance (r) from the axis of rotation:

τ = F * r

Rearranging the formula and substituting the given values:

α = τ / I = (98 N * 6 m) / 6120 kg · m^2 = 0.098 rad/s^2

Therefore, the initial angular acceleration of the rider is 0.098 rad/s^2.

C) The relationship between angular velocity (ω) and time (t) is given by the equation ω = α * t. Rearranging the formula to solve for time:

t = ω / α

The rider's velocity can be converted to angular velocity using the formula v = r * ω. Rearranging the formula to solve for angular velocity:

ω = v / r = 5 m/s / 6 m = 0.8333 rad/s

Substituting the values into the equation, we get:

t = 0.8333 rad/s / 0.098 rad/s^2 = 8.5 s

Therefore, the time required for the rider's velocity to reach 5 m/s is 8.5 seconds.

D) To find the mass per second that must leave the rocket to develop the given thrust (F), we can use Newton's second law of motion, which states that force (F) is equal to the rate of change of momentum (dp/dt). In this case, the force is equal to the thrust of the rocket, and the change in momentum is the mass per second leaving the rocket (dm/dt) multiplied by the exit velocity (v):

F = dm/dt * v

Rearranging the formula and substituting the given values:

dm/dt = F / v = 98 N / 390 m/s = 0.2513 kg/s

Therefore, the mass per second that must leave the rocket to develop the thrust of 98 N is 0.2513 kg/s.

To learn more about the moment of inertia click here

https://brainly.com/question/31045808

#SPJ11

uranus and neptune are like the other jovian planets because they:

Answers

Uranus and Neptune are like the other Jovian planets because they have a lot of gaseous composition, they lack a solid surface, and they are situated far from the sun.

The Jovian planets are four planets in the outer solar system that are gas giants, also known as the gas planets. They are Jupiter, Saturn, Uranus, and Neptune. In terms of the composition of Uranus and Neptune, they contain methane, ammonia, water, and other elements that form gas. Like the other Jovian planets, they lack a solid surface, and they are situated far from the sun.

The rings of Uranus and Neptune are fainter and less complex than the rings of Jupiter and Saturn, but they share certain features. Both Uranus and Neptune are thought to have a small rocky core surrounded by a mix of rock and ice, then a thick layer of metallic hydrogen, and an atmosphere mainly of molecular hydrogen and helium. So therefore because gaseous composition, lack a solid surface, and situated far from the sun, Uranus and Neptune are like the other Jovian planets.

To know more about Jovian planets visit:

https://brainly.com/question/31384996

#SPJ11

The moon has no atmosphere. Predict what would happen if an astronaut oro
hammer and a feather at the same time from the same height.

Answers

Answer:

They would all most likely have the same weight

Explanation:

Think about it the smaller the person or object the smaller the weight. But theyre all the same height now. And its not like you don't have any weight in the moon. So in conclusion they would all be the same weight

In the circuit shown, serves as an electronic switch. If Vin is very small, determine W/ such that the circuit attenuates the signal by only 5%.Assume Va = 2.1Vand R = 1750. Assume an NMOS transistor with k'=800 A/V2 and VTh=0.5V

Answers

To attenuate the signal by only 5%, the width-to-length ratio (W/L) of the NMOS transistor should be approximately 13.125.

To determine the required W/L ratio, we need to calculate the voltage gain of the circuit and find the value of W/L that corresponds to a 5% attenuation.

First, let's analyze the circuit. We have an NMOS transistor connected in a common-source configuration, where Vin is the input voltage, Va is the gate voltage, and Vout is the output voltage.

               _______________

              |               |

  Vin -------|               |

              |               |

              |               |

              |     NMOS      |------ Vout

              |               |

              |               |

              |               |

              |_______________|

               

The voltage gain (Av) of the NMOS transistor in the common-source configuration can be approximated as:

Av = -k' * (W/L) * (Vin - VTh) * (1 + λ * Vout)

where k' is the transconductance parameter, W/L is the width-to-length ratio, Vin is the input voltage, VTh is the threshold voltage, λ is the channel-length modulation parameter, and Vout is the output voltage.

Since the question states that Vin is very small, we can assume that the voltage drop across R is negligible. Therefore, Va will be approximately equal to Vin.

Va = Vin

We want the circuit to attenuate the signal by only 5%. This means the output voltage (Vout) should be 95% of the input voltage (Vin).

Vout = 0.95 * Vin

Substituting Va = Vin and Vout = 0.95 * Vin into the voltage gain equation, we get:

0.95 * Vin = -k' * (W/L) * (Vin - VTh) * (1 + λ * 0.95 * Vin)

Rearranging the equation, we have:

-k' * (W/L) * (Vin - VTh) * (1 + λ * 0.95 * Vin) = 0.95 * Vin

Simplifying, we get:

-k' * (W/L) * (1 + λ * 0.95 * Vin) = 0.95

Since Vin is very small, we can assume that λ * 0.95 * Vin is negligible compared to 1. Therefore, we can approximate the equation as:

-k' * (W/L) = 0.95

Now, let's substitute the given values:

k' = 800 A/V^2

VTh = 0.5 V

-800 * (W/L) = 0.95

Solving for W/L, we find:

W/L = 0.95 / -800 ≈ -0.0011875

The W/L ratio cannot be negative, so we take the absolute value:

W/L ≈ 0.0011875

Finally, we can calculate the width (W) for a given length (L). Assuming L = 1 (arbitrary units), we have:

W = (W/L) * L ≈ 0.0011875 * 1 ≈ 0.0011875

To attenuate the signal by only 5%, the width-to-length ratio (W/L) of the NMOS transistor should be approximately 0.0011875 (or 13.125 if the length is assumed to be 1 unit).

To learn more about transistors, visit    

https://brainly.com/question/1426190

#SPJ11

true/false. the sun radiates at an effective temperature of 5780 k and has a radius of about 696000 km

Answers

True. The Sun radiates at an effective temperature of 5780 K and has a radius of about 696,000 km.

The Sun's effective temperature refers to the temperature at which a black body (an idealized object that absorbs all incident radiation) would emit the same amount of radiation as the Sun. This value is approximately 5780 K, representing the temperature of the Sun's photosphere, the visible surface. Regarding the Sun's radius, it has an estimated average radius of about 696,000 km. This measurement defines the distance from the center of the Sun to its outer edge. The Sun is classified as a G-type main-sequence star, and its size is relatively large compared to other stars, making it an important reference point for understanding stellar characteristics.

To learn more about effective temperature, Click here:

https://brainly.com/question/30799008

#SPJ11

A wave created by a certain source travels from medium 1 into another medium 2. It is noticed that its velocity is faster in medium 2 than in medium 1. Three students are discussing what happens to the properties of the wave as it moves into medium 2. Student 1: The frequency of this wave increases as this wave moves into medium 2 in order to keep the equation of the velocity of a wave valid. Student 2: No, the frequency of the wave will remain the same as it is only dependent on the source, it will be the wavelength that will increase in order to keep the equation of the velocity of a wave valid. Student 3: No, you are both wrong. Both parameters will adjust in order to keep the equation of the velocity of a wave valid. Which one of these students do you agree with? Justify your response with words and or equations.

Answers

I agree with Student 2: The frequency of the wave will remain the same as it is only dependent on the source, while the wavelength will increase as the wave moves into medium 2.

The equation that relates the velocity (v), frequency (f), and wavelength (λ) of a wave is:

v = f * λ

According to this equation, if the velocity increases in medium 2 compared to medium 1, and the frequency remains constant (as stated by Student 2), then the only way to maintain the equation is for the wavelength to increase in medium 2.

This behavior can be explained by the fact that different media have different properties, such as density and elasticity, which affect the propagation of the wave. When a wave travels from one medium to another, the speed of the wave can change. However, the frequency of the wave is determined by the source and remains constant. Therefore, in order to maintain the equation v = f * λ, the wavelength must adjust to compensate for the change in velocity.

In summary, Student 2 is correct in stating that the frequency of the wave will remain the same, while the wavelength will increase as the wave moves into medium 2 to keep the equation of the wave velocity valid.

To know more about frequency here

https://brainly.com/question/14316711

#SPJ4

Other Questions
How many real solutions exist for this system of equations? Y = -x + 1 y = -x2 + 4x 2 A. Zero B. One C. Two D. Infinite Of all the reform movements in America during the 1800s, which one was the most important? What still needs to be reformed in America? wae21q42rwe2q4q2rwe3rq244e2eq2q22q A rectangular prism has a base perimeter of 28 inches and a height of 6 inches. What is the lateral surface area of the prism? Explain how the broad interpretation of the Commerce Clause has affected the law since Roosevelt's time as President. List at two major acts that have come from the broad interpretation. Using Starbucks coffee as your good,explain each of the following using only a single sentence for each.1pts.each a.Income Effect b.Substitution Effect c.Law of Diminishing Marginal Returns 2. For each situation, determine if the resulting change is in the given market is a change in demand or guantity demanded.1 pt.each) a. The price of vegetable oil increases,market for olive oil b.The price of vegetable oil increases,the market for popcorn c. The price of olive oil decreases,the market for olive oil 3.For each situation, determine if the resulting change is in supply or guantity supplied.(1 pt. each) a.The price of crude oil decreases,the market for crude oi b.The price of crude oil decreases,the market for gasoline c.The price of gasoline increases, the market for gasoline 4.Look at the graph on the reverse side.1 pt.each a.Is this a shortage or a surplus? How do you know? b.What does the situation in part a cause to occur? c.What does the effect in part b cause to occur? find the area of this polygon whats the answer to this explain what federalism is and the powers of the state of Texasin the U.S. constitutional (federal) context. In desperate need of help. If anyone could help it would be greatly appreciate. Will rate brainliest! Solve the quadratic equation x2 10x + 14 = 4 by completing the square.Question 3 options:A) x = 5 B) x = 5 C) x = 7 D) x = 7 The aorta carries blood away from the heart and eventually branches into a large number of capillaries that distribute the blood to various body organs. If for an average person, the aorta has a radius of 1.2 cm and blood travels through it at a speed of 42 cm/s and the capillaries have an average radius of 5.0 10-4 cm and blood travels through them at a speed of 0.005 cm/s, determine the approximate number of capillaries in the human body. The EU has made changes in airline regulation that dramatically affect major European carriers such as British International Air, KLM, Air France, Alitalia, and Swiss. With ambitious expansion plans, British International Air (BIA) has decided it needs a second service hub on the continent, to complement its large Heathrow (London) repair facility. The location selection is critical, and with the potential for 4,000 new skilled blue-collar jobs on the line, virtually every city in Western Europe is actively bidding for BIA's business. After initial investigations by Holmes Miller, head of the Operations Department, BIA has narrowed the list to 9 cities. Each is then rated on 12 factors, as shown in the table below. Italy Rome City France Lyon 7 Germany Munich Bonn Berlin Genoa Paris Nice 9 8 8 7 8 6 10 6 6 8 6 8 7 Weight Milan 80 7 75 4 75 4 75 9 75 6 3 wo 00 00 00 7 6 8 8 3 9 1 9 6 5 3 4 5 3 9 9 7 3 7 10 65 5 5 6 2 9 9 3 8 8 Factor Factor Description 1 Financial incentives 2 Skilled labor pool 3 Existing facility 4 Wage rates 5 Competition for jobs Ease of air traffic 6 access 7 Real estate cost 8 Communication link Alternativeness to 9 relocating executives 10 Political considerations 11 Expansion possibilities 12 Union strength 35 3 6 5 5 7 4 3 6 7 7 30 7 6 9 8 8 8 8 8 15 3 7 2 9 6 7 1 4 4 7 9 8 8 8 1 9 10 10 6 10 5 1 7 1 4 5 3 4 6 5 15 2 3 3 5 6 6 5 7 a) Based on the given information, the best location for the aircraft servicing facility is with a total weighted score of 1. (Enter your response as an integer.) Question 11 PointThe period of time between 1920 and the U.S. entry into World War II has been called an age of isolationism.TrueFalseQuestion 21 PointFDR really wanted to help the Allies, especially the Brits, who after the French surrender in 1940 were the only ones actually fighting the Nazis until 1941, when there were a whole lot of Russians also fighting them.TrueFalseQuestion 31 PointD-day was the beginning of the end of the Nazis.TrueFalseQuestion 41 PointRussians did most of the fighting in Europe, losing at least 20 million people and in the end it was the Russians who captured Berlin, Germany.TrueFalseQuestion 51 PointThe United States dropped an atomic bomb on Hiroshima on August 6th and on Nagasaki on August 9th.TrueFalseQuestion 61 PointWho is held responsible for the deaths of millions of Jews during this time period?Adolf HitlerBenito MussoliniHideki TojoJoseph StalinQuestion 71 PointWhat was the legislation that authorized military aid (in the form of a loan) to countries after the war?Lend Lease ActForeign Aid ActDollar DiplomacyContainment of CommunismQuestion 81 PointWorld War II brought about even more governmental intervention and control than we had seen in World War I.TrueFalseQuestion 91 PointThe war kicked the American economy into overdrive. By 1944 American factories were producing an airplane every five minutes and a ship everyday.TrueFalseQuestion 101 PointGovernment expenditures during war were twice the amount they had been in the previous 150 years.TrueFalseQuestion 111 PointLos Angeles became the second largest manufacturing center in the country, meaning that it was not built by Hollywood, it was built by World War II.TrueFalseQuestion 121 PointOrganized labor continued to grow as well, with union membership soaring from around 9 million in 1940 to almost 15 million in 1945TrueFalseQuestion 131 PointIn 1944 FDR called for a new Economic Bill of Rights that would expand governmental power in order to create full employment, and guarantee an adequate income, medical care, education, and housing to all Americans.TrueFalseQuestion 141 PointFDRs Economic Bill of Rights did not happen largely because Southern Democrats in the House and Senate didnt want it to because it would have meant a larger role for unions and also extending greater equality to African Americans, and they werent about to let that happen.TrueFalseQuestion 151 PointExecutive Order 9066 in February 1942 expelled all persons of Japanese descent from the west coast. 70% of Japanese Americans lived in California and as a result of this order more than 110,000 people were sent to internment camps where they lived in makeshift barracks under the eyes and searchlights of guards. (almost like Nazi concentration camps, but in America)TrueFalse What is the median of the data set? {5, 3, 4, 2, 6} Enter your answer in the box. Round to the nearest tenth. The best answer will receive brainiest. Cedar Retailer acquired inventory for $70,000. Cedar received a cash discount that is treated as income of $900 and paid a freight-in cost of $1,500. Cedar sold 70% of its inventory. Beginning and Ending Inventory is 0.00.Calculate COGS Find the trigonometric ratios as simplified fractions and as decimals to the nearest thousandths (3 decimal places)16 34HElp me plssss ;-; What is a population bottleneck? The logging company would like to use its sample to provide convincing statistical evidence that over 50 percent of the trees in the forest are spruce trees. The logging company has decided to use a chi-square goodness-of-fit test to justify its claim. Why is the chi-square goodness-of-fit test not an appropriate procedure for the logging company to use Use the box method to distribute and simplify (2 + 1)(2x - 3). Drag and drop theterms to the correct locations of the table.